DIY Christmas Light Kit for Your House

Pro-grade C9 lights for your house, in one box. Pick your kit:

500 ft C9 Christmas light kit with 12-inch spacing: socket wire, 500 warm white bulbs, 500 clips and 250 ft zip cord

500 ft Kit, 12-inch spacing

500 bulbs, 500 clips, plugs, zip cord and timer. Fuller look.
$1,199 + free shipping

Shop 12-inch kit

500 ft C9 Christmas light kit with 15-inch spacing: socket wire, 400 warm white bulbs, 400 clips and 250 ft zip cord

500 ft Kit, 15-inch spacing

400 bulbs, 400 clips, plugs, zip cord and timer. Lower cost.
$1,099 + free shipping

Shop 15-inch kit

What’s in the box:

  1. C9 socket wire
  2. Warm white LED bulbs
  3. Clips
  4. Male plugs
  5. Female plugs
  6. Zip cord
  7. Photocell timer
  8. Add-ons for metal roofs
  9. The finished look

1. C9 socket wire (500 ft)

Commercial-grade green C9 socket wire spool for cut-to-length Christmas lights
Commercial-grade C9 socket wire spool.
Green SPT-1 C9 socket wire on a spool with empty sockets
Empty sockets every 12 or 15 inches.

What it does: Holds your bulbs at an even 12 or 15 inches. You cut it to fit each roof edge exactly.

How to use it:

  1. Start at the end of the roof closest to your outdoor outlet.
  2. Unroll the wire along the gutter as you clip it up (step 3).
  3. At the end of the roof edge, cut the wire halfway between two sockets.
  4. Snap a male plug on the start of the run (step 4).

Not sure how much wire you need? Measure your roofline without a ladder.

2. Warm white Elite C9 LED bulbs

Warm white Elite C9 LED faceted Christmas light bulb
Warm white Elite C9 LED bulb (2800K to 3200K).
C9 LED bulbs lit on green socket wire
Bulbs lit on the socket wire.

What it does: Shatterproof polycarbonate bulbs that will not crack or yellow like cheap polystyrene bulbs.

How to use it:

  1. Screw one bulb into every socket until snug. Do not overtighten.
  2. Bulb the wire on the ground before it goes up, so you spend less time on the ladder.
  3. Keep a few spares in your storage bin for next year.

Want a different white? See warm vs pure vs cool white.

3. C9 clips (one per bulb)

White C9 Best Clip that holds C9 sockets on gutters and shingles
White C9 Best Clip for gutters and shingles.
White C9 Christmas light clip, front view showing the socket ring
The ring holds the socket.

What it does: Holds each socket upright so every bulb points the same way.

How to use it:

  1. Push the socket into the clip ring.
  2. Slide the clip onto the gutter lip, or tuck it under the edge of a shingle.
  3. Keep the bulbs standing straight up and evenly spaced.

Different roof? See the clips guide.

4. Male plugs (50)

Green Gilbert male plug for SPT-1 Christmas light wire
Green Gilbert male plug for SPT-1 wire.

What it does: Turns the cut end of the wire into a plug that goes into power.

How to use it:

  1. Open the plug.
  2. Lay the cut wire in the channel, pushed all the way to the end.
  3. Match the ribbed side of the wire to the wide blade side of the plug.
  4. Press the plug closed until it clicks. The prongs bite through the insulation. No stripping.
  5. Plug it in and test before you hang it.

5. Female plugs (50)

Green Gilbert female plug with knockout tab for SPT-1 Christmas light wire
Green Gilbert female plug with knockout tab.

What it does: Lets you plug one run or lead into another.

How to use it:

  1. Install it on the wire the same way as the male plug.
  2. Use it at the end of a lead so a light run can plug into it.
  3. Close off the last run with a female plug or an end cap (step 8).

6. Green zip cord (250 ft)

250 ft spool of green SPT-1 zip cord used to make custom Christmas light extension leads
250 ft spool of green SPT-1 zip cord.

What it does: Plain wire for custom leads from the roof to the outlet, or to jump across a gap like a garage door.

How to use it:

  1. Measure from the start of the light run to the outlet or timer.
  2. Cut the zip cord to that length.
  3. Put a male plug on one end and a female plug on the other.
  4. Run it down the downspout or trim so it blends in.

Keep it safe in the rain: stop the GFCI from tripping.

7. Photocell outdoor timer

Outdoor photocell timer with grounded outlets that turns Christmas lights on at dusk
Photocell outdoor timer.

What it does: Turns your lights on at dusk every night, automatically.

How to use it:

  1. Plug the timer into an outdoor GFCI outlet.
  2. Plug your lead into the timer.
  3. Set it to turn on at dusk and off after the number of hours you want.
  4. Keep the light sensor uncovered so it can see when it gets dark.

How many runs can one outlet handle? See lights per outlet.

8. Add-ons for metal roofs and clean ends

Red and blue C9 LED bulbs held on magnetic clips on green socket wire

Magnetic C9 clips

For metal roofs, steel gutters and trim. Snap the socket in and set it on the metal.

Shop magnetic clips

Clear end cap sealing the end of green SPT-1 wire

Clear end caps

Push onto the cut end of the last run to seal it.

Shop end caps

9. The finished look

Home with C9 Christmas lights on the roofline at night
Cut to the exact roofline: no extra strand off the gutter.

Full walkthrough: how to hang C9 lights on a roofline. Rather not climb? Find an installer near you.

Shop the 500 ft Christmas light kit

Every part, photographed: what’s in a Christmas light kit.

Quick answers

Can a homeowner use a contractor Christmas light kit?

Yes. A contractor kit is the same commercial-grade C9 socket wire, LED bulbs, clips and plugs professional installers hang. The 500 ft kit is the smallest size and covers a large roofline, with wire left over for a garage, fence line or next year’s additions.

How many feet of Christmas lights do I need for my house?

Measure every roof edge you want to light and add about 10% for drops to the outlet and corners. Many single-story homes land between 150 and 250 feet of roofline; two-story homes with peaks often run more.

Should I get 12-inch or 15-inch spacing?

12-inch spacing puts one bulb every foot for a fuller, brighter line and is the classic residential look. 15-inch spacing uses about 20% fewer bulbs and costs less, and still looks clean from the street.

Can I cut the socket wire to fit my roof?

Yes. Socket wire is made to be cut between sockets. Snap a male plug on the start of each run and close the end with a female plug or an end cap, so every run fits your roofline exactly with no extra strand hanging off the gutter.

Is it cheaper to buy a kit or hire an installer?

Professional installation commonly runs about $4 to $12 per foot each season. A 500 ft kit is a one-time purchase of $1,099 to $1,199 that you reuse for years, but you do the ladder work, takedown and storage yourself.

Are LED C9 bulbs safe to leave on all night?

Commercial LED C9 bulbs run cool and draw very little power. Use a GFCI-protected outdoor outlet and the photocell timer included in the kit so the lights turn on at dusk and you are not running them all day.

ChristmasPlug Team
Author: ChristmasPlug Team

The ChristmasPlug team: Christmas light installers with nine years in the trade.

Written by the ChristmasPlug team
Our team has installed Christmas lights for nine years, from single-story rooflines to large HOA and commercial displays. About ChristmasPlug

Refunds & cancellation · GOAT Verified