Commercial 5mm LED mini lights for wrapping trees, bushes and columns. Pick your strand:
50-count, 6-inch, 6-pack
About 24 ft strands · 6 per set
$94.99
$15.83 per strand · Free shipping
In this guide:
- Pick your strand
- Colors
- Wrap a tree trunk
- Wrap the limbs
- Bushes and columns
- Power and connecting strands
- How many to buy
1. Pick your strand


- 70-count, 4-inch (23.5 ft): the most light per foot. Best for trunks and big trees, with fewer connections.
- 50-count, 4-inch (17 ft): shorter strands. Easier on small trees and bushes.
- 50-count, 6-inch (about 24 ft): a lighter, more open look for bushes, railings and greenery.
- All are 5mm LED with sealed one-piece bulbs, rated up to 50,000 hours.
2. Colors
Warm white
Sun warm white
Pure white
Cool white
Multi
Green
Red
Red is available on the 70-count strands. Match your mini lights to your roofline bulbs. See the C9 bulb color guide.
3. Wrap a tree trunk

- Plug the first strand in at the base of the tree, at the outlet side.
- Wrap upward in a steady spiral, about 3 to 4 inches between wraps for a full look.
- Keep the wire tight to the bark so the lights don’t sag.
- When a strand ends, plug the next one into its end and keep wrapping.
- At the top, tuck the last end into a branch fork so it stays put.
Need the exact strand count? Use the formula in how many mini lights to wrap a tree.
4. Wrap the limbs

- Agree with the customer how far out the limbs get wrapped, like “main limbs to 10 feet out.”
- Start each limb where it meets the trunk and wrap out toward the tip.
- Use the same spacing as the trunk so the whole tree looks even.
- Wrap back toward the trunk on long limbs so the plug end returns where the power is.
- Big trees can take 100 strands or more. Use a lift for anything you can’t reach safely.

5. Bushes and columns

- Bushes: weave strands in and out across the top and sides, not just around the outside.
- Columns: wrap in a tight spiral like a trunk, or straight up and down for a candy-cane stripe.
- 6-inch strands go further on big hedges with a lighter look.
6. Power and connecting strands

- Each strand uses about 4.8 watts.
- You can connect up to 45 strands end to end.
- Plug into an outdoor GFCI outlet with a timer.
- Need a cord from the tree to the outlet? Make one any length with plugs and extension wire.
- Keep connections off the wet ground. See how to seal Christmas lights.
7. How many to buy

- Measure around the trunk in feet and how high you will wrap.
- Wraps = height in inches ÷ inches between wraps. Feet of lights = wraps × trunk circumference.
- Divide by 23.5 ft (70-count) or 17 ft (50-count). Round up and add 10%.
- Worked examples: how many mini lights to wrap a tree. Pricing the job: cost to wrap a tree.
Quick answers
What are commercial mini lights?
Commercial mini lights are 5mm LED strands with sealed one-piece bulbs that resist moisture and corrosion. They are sold by the case for wrapping trees, bushes and columns, and are rated for long outdoor use.
Should I buy 50-count or 70-count mini lights?
70-count strands are 23.5 ft with 4-inch spacing and need fewer connections on big trees. 50-count strands are 17 ft with 4-inch spacing, or about 24 ft with 6-inch spacing for a lighter look on bushes.
How many mini light strands can I connect end to end?
These LED strands use about 4.8 watts each, and up to 45 can be connected end to end.
How far apart should I wrap mini lights on a tree?
About 3 to 4 inches between wraps looks full and bright. About 6 inches gives a lighter look and uses fewer strands.
How much do commercial mini lights cost?
About $12.46 to $16.67 per strand depending on length and pack size, with free shipping.
